See the (badly rendered and not perfectly accurate) image below for what I mean.Īnd if so, what kind of steel should I use? I don't know a ton about metallurgy, and there are a lot of big terms out there like Rockwell C, air-hardening, and other stuff. So for a 3 hammer, you need a minimum of 60, 75 is better, 100 pounds is good. You can purchase split rail fencing materials at most hardware stores, but the original way to do it is to split the logs yourself. Add some wire mesh to make the enclosure more secure. For forging a knife, you want at least twenty times of mass of the hammer. For a more modern take, fence posts are drilled all the way through so that the rails can be inserted into the slots. Even an unhardened Rc42-45 cast steel anvil will work fine if it has enough mass. This would allow for a stronger piece of steel to become the main surface of my anvil, and also creates a table. Mass and inertia is what an anvil is all about. So, in discussion with my shop teacher, I've been looking into welding a piece of steel onto the face of the track, which I have already flattened. I think that the best height is: When you are making the cut, grinder sets to somewhat same level with your pelvis, or little lower. I've seen several drawings of RR anvils that are turned on their end which I don't think is for me. Being very inexperienced at smithing, I'd rather not limit myself to such a small 'whacking surface' like the ones shown Link removed Clamp the piece of track to suitable height. That being said, I want to make this piece of rail as useful as possible. But I'm trying to start blacksmithing as part of a project for school, and I want to be show that you don't have to drop hundreds of dollars on an actual London Pattern anvil. Now, before y'all start cringing, I understand that RR Track is not the ideal anvil material. Protective gear is advisable, especially for the eyes and ears.I got 12" of railroad track given to me as a gift, and I intend to make it into an anvil. If you use a sledgehammer head be careful that it's forged and not cast iron for the same reason. railroad concerns took over and converted much of the original Take in the many. The same goes for some hammer heads, don't hit two hammers together if they're cast. Anvil Graphic Black org has listings of Iron Mountain Best Western and. People are right to say that cast iron is no good, it's far too brittle and could be dangerous because bits can fly off like shrapnel. For things like this it's best to treat is as a bit of fun - mooch around waiting for a good opportunity rather than treating it as a shopping expedition. I could do that, then weld some clips to the plate and use the clips to bolt the. This guy welded a piece of steel plate to the bottom of the anvil. I thought about tack welding the plates to the track anvil and then use lag bolts to secure the plates the wooden base. You could end up with a real beauty of a small anvil for next to nothing if you're lucky, but it really is down to luck on the day. In this example the guy mounted the anvil on a couple of railroad plates. Some smaller anvils come with a chunky stand.Ī lot of engineering companies go bankrupt every year, check out the auctioneers and ask for a catalogue. You could drill and bolt several pieces together if you wanted to make it more easily portable, you could make a stand that way too. Ask to look in their scrap bin (it will be a big skip somewhere in the yard) and if you find a bit that's a bit too heavy they might even offer to chop it up into manageable sizes for you.įor these purposes you don't really need to worry about steel's metallurgy, you just need as big a lump of steel as you can reasonably lug about if you're going to. How to Use a USB Drive as a Secure Unlock Key for Your PC Horizon Chase Turbo s First. They will have guillotines that can cut through two inch steel plate as easily as you cut through paper with a pair of scissors. Railroad Track Anvil Vise Forge Blacksmith 7h ago Sartell 20. You could also try looking in the Yellow Pages for local fabrication shops, try to find a firm that makes heavy duty stuff. It weighs about 400lb, you can really build up your arm muscles trying to bend it. I bought a lovely anvil from the local scrap merchant for 40 quid. anvil for jewelers and precious metalsmiths usually weighs between 45 and 75. Scrap steel fetches anything between practically nothing and about 100 quid per tonne depending on the state of the economy. secure in place and tend to ' dance ' around the bench - top. Don't let them fleece you for it though, they have that kind of reputation. Most scrap merchants will be only too pleased to get rid of heavy lumps of steel because they're too thick to go through their metal chewing machinery.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |